Magellan MG5000 Installationshandbuch PDF herunterladen (Seite 26)

22 Reference & Installation Manual

6.6.3 Programming the Remote Control Buttons

Sections [611] to [642]: Remote Controls 1 to 32 respectively

Each remote control can be programmed to perform up to 4 different actions. Each digit in sections [611] to [642]

represents a button or combination of buttons.

Warning: When section [610] is accessed, the MG5000 will copy the saved value of that section to all

remotes.

6.7 Wireless Keypad Assignment

Sections [570] to [573]

Automatic Assignment: After panel power-up, the control panel will open a 10 minute window for Automatic Assignment. Press

and hold the [] and [BYP] key for three seconds on the respective keypad. The keypad is assigned to the control panel. Up to 4

wireless keypads can be assigned within the ten minute window.

Standard Assignment: Press [

ENTER]. Enter your [INSTALLER CODE] or [MAINTENANCE CODE].

Go to section(s) [570] = Keypad 1, [571] = Keypad 2, [572] = Keypad 3, or [573] = Keypad 4.

Press and hold the [] and [

BYP] key for three seconds on the respective keypad. The keypad is assigned to the control panel.

Alternatively, enter the serial number of the MG32LRF into one of the four sections to assign it to the panel.

6.8 Viewing the Wireless Keypad Signal Strength

Sections [575] to [578]

Once wireless keypads have been installed and assigned to the Magellan MG5000, the signal strength of each transmitter can be

verified in sections [575] to [578]. Each section represents the signal strength viewer for a specific keypad. For example, section

[575] is the viewer for keypad 1 and section [578] is the viewer for the keypad 4. Sometimes moving the keypad by a small

amount will greatly increase the signal reception.

How Do I Delete a Remote Control?

1) Press the [ENTER] key.

2) Enter your [

INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (default 1111/111111)

3) Enter the desired [SECTION NUMBER] (from sections [651] to [682]).

4) Press the [0] button six times to delete the serial number.

How Do I Program the Remote Control’s Buttons?

1) Press the [ENTER] key.

2) Enter your [

INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (default 1111/111111)

3) Enter the desired [SECTION NUMBER] (from sections [610] to [642]).

4) Enter the [

HEXADECIMAL VALUE] (0 to F) of the desired button option from Table 5 on page 22 in the appropriate

space. If you do not wish to program a button combination, press the [

SLEEP] key to skip.

Table 5: Button Options

[0] = Button Disabled* [8] = Generate a Panic 1 Alarm

[1] = Regular/Regular Force arming [9] = Generate a Panic 2 Alarm

[2] = Stay/Stay Force arming [0] or [0(10)] = Generate a Panic 3 Alarm

[3] = N/A [

OFF] = Activates any PGMs that have Event Group #08 as their Activation Event

[4] = Sleep/Sleep Force arming [

BYP] = Activates any PGMs that have Event Group #09 as their Activation Event

[5] = N/A [

MEM] = Activates any PGMs that have Event Group #10 as their Activation Event

[6] = N/A [

TBL] = Activates any PGMs that have Event Group #11 as their Activation Event

[7] = N/A

[] = Paramedic alarm

* If you do not enter a value for a button, that button is disabled.

How Do I View a Wireless Keypad’s Signal Strength?

1) Press the [ENTER] key.

2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (default 1111/111111)

3) Enter the desired [SECTION NUMBER] (from sections [575] to [578]).

4) Press the keypad’s anti-tamper switch or open the corresponding keypad zone.

5) The keypad will illuminate numbers 1 to 10.

Signal Strength Indicator

8 to 10 / 3 beeps = Best signal 5 to 7 / 2 beeps = Average signal 1 to 4 / 1 beep = Weak signal (Relocate)

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 55 56

Kommentare zu diesen Handbüchern

Keine Kommentare

Magellan MG5000 Installationshandbuch Seite 26

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Magellan MG5000